Fbtft st7789v

HamsterBear Linux ST7789V FBTFT驱动适配

平台 - F1C200s
Linux版本 - 5.18
TFT屏 - 1.69寸IPS高清ST7789V

修改设备树，在spi0节点下添加

&spi0 {
        pinctrl-names = "default";
        pinctrl-0 = <&spi0_pd_pins>;
        status = "okay";
        spi-max-frequency = <50000000>;

        st7789v: st7789v@0 {
                #address-cells = <1>;
                #size-cells = <1>;
                compatible = "sitronix,st7789v";
                reg = <0>;
                spi-max-frequency = <50000000>;
                rgb;
                buswidth = <8>;
                rotate = <90>;
                fps = <60>;
                spi-cpol;
                spi-cpha;
                reset-gpios = <&pio 4 10 GPIO_ACTIVE_HIGH>;     /* PE10 */
                dc-gpios = <&pio 2 3 GPIO_ACTIVE_LOW>;          /* PC3 */
                debug = <1>;
        };
};

确定内核config打开

需要注意的是，fbtft的驱动只有在内核framebuffer相关驱动开启后才会出现，所以要先开启fb驱动支持 Device Drivers -> Graphics support -> Frame buffer Devices --->，编译进内核

可根据需要将控制台映射到fb功能开启

这里我同时选择了16色的Tux 启动logo

然后寻找fbtft驱动，路径如下： Device Drivers -> Staging drivers -> Support for small TFT LCD display modules --->，编译进内核

修改`drivers/staging/fbtft/fb_st7789v.c`，如下几处

修改init函数，该初始化序列参考自厂家

static int init_display(struct fbtft_par *par)
{
        int rc;

        par->fbtftops.reset(par);
        mdelay(100);
        rc = init_tearing_effect_line(par);
        if (rc)
                return rc;

        write_reg(par, 0x11); //Sleep out
        mdelay(120);     //Delay 120ms

        //************* Start Initial Sequence **********//
        write_reg(par, 0x36, 0x00);

        write_reg(par, 0x3A, 0x05);

        write_reg(par, 0xB2,0x0C,0x0C,0x00,0x33,0x33);

        write_reg(par, 0xB7,0x35);

        /* VCOM  = 1.35V */
        write_reg(par, 0xBB, 0x32);

        write_reg(par, 0xC2, 0x01);

        /* GVDD = 4.8V */
        write_reg(par, 0xC3,0x15);

        /* VDX = 0V */
        write_reg(par, 0xC4, 0x20);

        /* FPS = 60Hz */
        write_reg(par, 0xC6,0x0F);

        write_reg(par, 0xD0, 0xA4, 0xA1);

        write_reg(par, 0xE0,0xD0,0x08,0x0E,0x09,0x09,0x05,0x31,0x33,0x48,0x17,0x14,0x15,0x31,0x34);

        write_reg(par, 0xE1,0xD0,0x08,0x0E,0x09,0x09,0x15,0x31,0x33,0x48,0x17,0x14,0x15,0x31,0x34);

        write_reg(par, MIPI_DCS_ENTER_INVERT_MODE);

        write_reg(par, MIPI_DCS_SET_DISPLAY_ON);

        return 0;
}

2，修改display参数

static struct fbtft_display display = {
        .regwidth = 8,
        .width = 240,
        .height = 280,  /* 根据你的屏幕分辨率确定 */
        .gamma_num = 2,
        .gamma_len = 14,
        .gamma = HSD20_IPS_GAMMA,
        .fbtftops = {
                .init_display = init_display,
                .write_vmem = write_vmem,
                .set_var = set_var,
                .set_gamma = set_gamma,
                .blank = blank,
        },
};

修改`drivers/staging/fbtft/fbtft-core.c`，如下几处

添加头文件

#include <linux/of.h>
#include <linux/of_gpio.h>

修改fbtft_request_one_gpio函数
```
  {                           
```
href="#__codelineno-4-1">static int fbtft_request_one_gpio(struct fbtft_par *par, const char *name, int index, struct gpio_desc **gpiop) span> int ret, gpio; struct device *dev = par->info->device; struct device_node *np = dev->of_node; enum of_gpio_flags flags; /* Get GPIO from device tree */ gpio = of_get_named_gpio_flags(np, name, index, &flags); if (gpio < 0) { return 0; } ret = devm_gpio_request_one(dev, gpio, (flags & OF_GPIO_ACTIVE_LOW)?GPIOF_OUT_INIT_LOW:GPIOF_OUT_INIT_HIGH, dev->driver->name); if (ret) { dev_err(dev, "Failed to request %s GPIO%d\n", name, gpio); return -ENODEV; } *gpiop = gpio_to_desc(gpio); fbtft_par_dbg(DEBUG_REQUEST_GPIOS, par, "%s: '%s' GPIO%d\n", __func__, name, gpio); return ret; }

修改fbtft_request_gpios函数

static int fbtft_request_gpios(struct fbtft_par *par)
{
        int i;
        int ret;

        ret = fbtft_request_one_gpio(par, "reset-gpios", 0, &par->gpio.reset);
        if (ret)
                return ret;
        ret = fbtft_request_one_gpio(par, "dc-gpios", 0, &par->gpio.dc);
        if (ret)
                return ret;
        ret = fbtft_request_one_gpio(par, "rd-gpios", 0, &par->gpio.rd);
        if (ret)
                return ret;
        ret = fbtft_request_one_gpio(par, "wr-gpios", 0, &par->gpio.wr);
        if (ret)
                return ret;
        ret = fbtft_request_one_gpio(par, "cs-gpios", 0, &par->gpio.cs);
        if (ret)
                return ret;
        ret = fbtft_request_one_gpio(par, "latch-gpios", 0, &par->gpio.latch);
        if (ret)
                return ret;
        for (i = 0; i < 16; i++) {
                ret = fbtft_request_one_gpio(par, "db-gpios", i,
                                             &par->gpio.db[i]);
                if (ret)
                        return ret;
                ret = fbtft_request_one_gpio(par, "led-gpios", i,
                                             &par->gpio.led[i]);
                if (ret)
                        return ret;
                ret = fbtft_request_one_gpio(par, "aux-gpios", i,
                                             &par->gpio.aux[i]);
                if (ret)
                        return ret;
        }

        return 0;
}

修改fbtft_set_win_addr函数因为st7789v支持到240x320的分辨率，但是我这块屏是240*280，所以x start和x end都有偏移, 这个偏移值也是我从厂家源码中参考的。

static void fbtft_set_addr_win(struct fbtft_par *par, int xs, int ys, int xe,
                               int ye)
{
        xs = xs + 20;
        xe = xe + 20;
        write_reg(par, MIPI_DCS_SET_COLUMN_ADDRESS,
                  (xs >> 8) & 0xFF, xs & 0xFF, (xe >> 8) & 0xFF, xe & 0xFF);

        write_reg(par, MIPI_DCS_SET_PAGE_ADDRESS,
                  (ys >> 8) & 0xFF, ys & 0xFF, (ye >> 8) & 0xFF, ye & 0xFF);

        write_reg(par, MIPI_DCS_WRITE_MEMORY_START);
}

修改fbtft_reset函数 st7789v是low level reset

static void fbtft_reset(struct fbtft_par *par)
{
        if (!par->gpio.reset)
                return;

        fbtft_par_dbg(DEBUG_RESET, par, "%s()\n", __func__);

        gpiod_set_value_cansleep(par->gpio.reset, 1);
        usleep_range(20, 40);
        gpiod_set_value_cansleep(par->gpio.reset, 0);   /* Low level reset */
        msleep(120);

        gpiod_set_value_cansleep(par->gpio.reset, 1);  /* Activate chip */
}

Fbtft st7789v

HamsterBear Linux ST7789V FBTFT驱动适配

修改设备树，在spi0节点下添加

确定内核config打开

修改drivers/staging/fbtft/fb_st7789v.c，如下几处

修改drivers/staging/fbtft/fbtft-core.c，如下几处

最后附上两个文件的直观patch

修改`drivers/staging/fbtft/fb_st7789v.c`，如下几处

修改`drivers/staging/fbtft/fbtft-core.c`，如下几处